Garz & Fricke Linux BSP V1.7.0				05.06.2012

Released by Tim Jaacks
Verified by Tim Jaacks

Reason for the release:
	* Touch problems on CUPID and NESO
	* Audio problems on NESO-LT
	* Board support for ECO-G45

Required PTXdist version: 2011.09.0
Required Toolchain:
	* OSELAS.Toolchain-1.99.3 (NESO, CUPID, NESO-LT, LIVIUS)
	* OSELAS.Toolchain-2011.03.1 (VINCELL)
	* OSELAS.Toolchain-2011.11.1 (ECO-G45)
Minimum required RedBoot version: 1.16r2757

Fully supported and tested hardware platforms in this release:
	* CUPID
	* NESO
	* NESO-LT
	* ECO-G45

All other platforms will probably work, but are to be used at own risk.

Supported Hardware:
* NESO:
	* General board support
	* UART1 (RS232)
	* UART3 (RS458)
	* UART5 (RS232)
	* USB Host
	* USB OTG (host mode only)
	* NFC
	* Display
	* Ethernet
	* UCB1400 Input Touchscreen
	* UCB1400 ALSA Sound device
	* RTC PCF8583 on I2C1
	* AT24 compatible EEPROM on I2C1
	* LEDs
	* PWM Backlight
	* MMC/SD-Card
	* Digital I/Os

* CUPID:
	* General board support
	* UART1 (RS232)
	* UART2 (RS232)
	* UART3 (RS485)
	* USB Host
	* USB OTG (device mode only)
	* NFC
	* Display
	* Ethernet
	* UCB1400 Resistive Touchscreen
	* Pinnacle Capacitive Touchscreen
	* UCB1400 ALSA Sound device
	* RTC PCF8583 on I2C1
	* AT24 compatible EEPROM on I2C1
	* LEDs
	* PWM Backlight
	* MMC/SD-Card
	* Flexcan1
	* Flexcan2
	* Digital I/Os

* NESO-LT:
	* General board support
	* UART1 (RS232)
	* UART3 (RS485)
	* USB Host
	* USB OTG (device mode only)
	* NFC
	* Display
	* PWM Backlight
	* Ethernet
	* CS4265 ALSA Sound device
	* RTC PCF8583 on I2C1
	* AT24 compatible EEPROM on I2C1
	* ADC/TSC Resistive Touchscreen
	* Pinnacle Capacitive Touchscreen
	* MMC/SD-Card
	* Flexcan1
	* Digital I/Os

* LIVIUS:
	* General board support
	* UART1 (RS232)
	* Ethernet
	* NFC
	* USB Host
	* USB Device
	* RTC PCF8583 on I2C1
	* AT24 compatible EEPROM on I2C1
	* MMC/SD-Card
	* Digital I/Os

* VINCELL:
	* General board support
	* UART1 (RS232)
	* UART2 (RS232/MDB)
	* UART3 (RS485)
	* Ethernet
	* USB HOST
	* NFC
	* Display
	* PWM Backlight
	* RTC DA9052 on I2C1
	* AT24 compatible EEPROM on I2C1
	* DA9052 Resistive Touchscreen
	* Pinnacle Capacitive Touchscreen
	* EDT FT5X06 Capacitive Touchscreen
	* SGTL5000 ALSA Sound device
	* MMC/SD-Card
	* CAN
	* Digital I/Os

* ECO-G45 (on base board):
	* DBGU (AT91Bootstrap, U-Boot, Linux)
	* Onchip UART with GPIO-selectable RTS/CTS
	* Onchip Ethernet (U-Boot, Linux)
	* Onchip NAND (AT91Bootstrap, U-Boot, Linux)
	* Battery-backed SRAM (U-Boot, Linux)
	* Automount of Battery-backed SRAM with a JFFS2 filesystem (Linux)
	* Onchip MMC/SD (Linux)
	* Onchip USB-Host (U-Boot, Linux)
		* USB Mass Storage (U-Boot, Linux)
		* UDisk/DBUS support for Hotplugging
	* Onchip USB-Device (Linux)
		* Serial gadget
		* Ethernet gadget
	* Onchip I2C (Linux)
	* SPI (Linux)
		* CS Encoding
	* GPIO (Linux)
		* Onchip GPIO (Linux)
	* EEPROM (U-Boot, Linux)
		* MAC-Addresses storage in EEPROM
	* RTC (Linux)
		* Onchip RTC
	* Onchip AT91 Timer / Counter Kernel API (Linux)
	* Onchip True Random Number Generator (Linux)
		* Rngd support
	* Onchip Graphic Controller
	* Onchip Touchscreen Controller
	* WM9705S AC97 Audio Codec
		* Headphone
		* Line Out
		* MIC In
		* Line IN

Enabled packages:
	* alsa-lib-1.0.23
	* alsa-utils-1.0.22
	* Bootstrap-v1.16
	* busybox-1.18.5
	* canutils-4.0.5
	* dbus-1.4.14
	* dbus-glib-0.92
	* DeviceKit-disks-009
	* dosfstools-3.0.9
	* e2fsprogs-1.41.14
	* eggdbus-0.6
	* expat-2.0.1
	* fbtest-20041102-1
	* fbutils-20041102-1
	* figlet-2.2.4
	* freetype-2.3.11
	* fstyp (Modified version from Garz & Fricke)
	* gdb-6.8/7.2 (platform dependent)
	* gfeeprom
	* glib-2.28.8
	* jpeg-8a
	* libmdb
	* libpng-1.2.44
	* libsocketcan-0.0.8
	* libusb-1.0.8
	* libusb-compat-0.1.3
	* linux-2.6.33/2.6.35/2.6.39 (platform dependent)
	* ltp-full-20110915
	* mtd-utils-1.3.1
	* nano-1.3.12
	* ncurses-5.9
	* ntpclient-2007
	* openssh-5.8p2
	* openssl-1.0.0d
	* polkit-0.96
	* procps-3.2.8
	* qt-everywhere-opensource-src-4.7.2
	* rng-tools-3
	* strace-4.5.20
	* tslib-1.0
	* u-boot-2011.06
	* udev-150/162/172 (platform dependent)
	* usbutils-0.90
	* util-linux-2.19.1
	* xconfig
	* zlib-1.2.5

Missing drivers and features:
	NESO:
		* USB OTG works only in host mode.
		* VPU driver is currently not implemented.
		* Video4L output driver is currently not implemented.

	CUPID:
		* USB OTG works only in device mode.
		* OpenVG is not supported yet.

	NESO-LT:
		* USB OTG works only in device mode.

	LIVIUS:
		* Display is not supported yet.
		* RS485 is not supported yet.
		* Analog I/O is not supported yet.
		* 1-Wire ist not supported yet.
		* UART 3 (RS232) is not supported yet.
		* Flexcan is not supported yet.

	VINCELL:
		* USB OTG is not supported.
		* SATA is not supported.

	ECO-G45:
		* USB-OTG is not supported.
		* WM959705S Touchscreen feature is possible by hardware but not supported.
		* Touchscreen is not filtered properly yet (In work. Original driver from ATMEL is not very good.)
		* Sound output has a click noise during start up.
		* AT45 SPI EEPROM not supported.

	General:
		* Video CODECs are not supported yet (and not possible by Hardware on ECO-G45).
		* 2D accelleration (where exists) is not supported (and not possible by Hardware on ECO-G45).

Changes:
	* Added new filters to tslib for better touchscreen precision on CUPID and NESO.
	* Fixed audio problem on NESO-LT (codec was not initialized in some scenarios).
	* Fixed USB OTG problem on NESO-LT (device mode did not work since 1.5.0).
	* Fixed capacitive touch problem on NESO-LT (did not work in last release).
	* Added CAN support on VINCELL.
	* Added board support for ECO-G45.


Garz & Fricke Linux BSP V1.6.0				08.05.2012

Released by Tim Jaacks
Verified by Tim Jaacks

Reason for the release:
	* MDB support for VINCELL

Required PTXdist version: 2011.09.0
Required Toolchain:
	* OSELAS.Toolchain-1.99.3 (NESO, CUPID, NESO-LT, LIVIUS)
	* OSELAS.Toolchain-2011.03.1 (VINCELL)
Minimum required RedBoot version: 1.16r2757

Fully supported and tested hardware platforms in this release:
	* VINCELL

All other platforms will probably work, but are to be used at own risk.

Supported Hardware:
* NESO:
	* General board support
	* UART1 (RS232)
	* UART3 (RS458)
	* UART5 (RS232)
	* USB HOST
	* USB OTG (only as slave, untested)
	* NFC
	* Display
	* Ethernet
	* UCB1400 Input Touchscreen
	* UCB1400 ALSA Sound device
	* RTC PCF8583 on I2C1
	* AT24 compatible EEPROM on I2C1
	* LEDs
	* PWM Backlight
	* MMC/SD-Card
	* Digital I/Os

* CUPID:
	* General board support
	* UART1 (RS232)
	* UART2 (RS232)
	* UART3 (RS485)
	* USB HOST
	* USB OTG (only as slave, untested)
	* NFC
	* Display
	* Ethernet
	* UCB1400 Resistive Touchscreen
	* Pinnacle Capacitive Touchscreen
	* UCB1400 ALSA Sound device
	* RTC PCF8583 on I2C1
	* AT24 compatible EEPROM on I2C1
	* LEDs
	* PWM Backlight
	* MMC/SD-Card
	* Flexcan1
	* Flexcan2
	* Digital I/Os

* NESO-LT:
	* General board support
	* UART1 (RS232)
	* UART3 (RS485)
	* USB HOST
	* NFC
	* Display
	* PWM Backlight
	* Ethernet
	* CS4265 ALSA Sound device
	* RTC PCF8583 on I2C1
	* AT24 compatible EEPROM on I2C1
	* ADC/TSC Resistive Touchscreen
	* Pinnacle Capacitive Touchscreen
	* MMC/SD-Card
	* Flexcan1
	* Digital I/Os

* LIVIUS:
	* General board support
	* UART1 (RS232)
	* Ethernet
	* NFC
	* USB Host
	* USB Device
	* RTC PCF8583 on I2C1
	* AT24 compatible EEPROM on I2C1
	* MMC/SD-Card
	* Digital I/Os

* VINCELL:
	* General board support
	* UART1 (RS232)
	* UART2 (RS232/MDB)
	* UART3 (RS485)
	* Ethernet
	* USB HOST
	* NFC
	* Display
	* PWM Backlight
	* RTC DA9052 on I2C1
	* AT24 compatible EEPROM on I2C1
	* DA9052 Resistive Touchscreen
	* Pinnacle Capacitive Touchscreen
	* EDT FT5X06 Capacitive Touchscreen
	* SGTL5000 ALSA Sound device
	* MMC/SD-Card
	* Digital I/Os

Enabled packages:
	* alsa-lib-1.0.23
	* busybox-1.18.5
	* ftpd support on top of tcpsvd (starting at system startup)
	* canutils-4.0.5
	* dosfstools-3.0.9
	* figlet-2.2.4
	* libusb-1.0.8
	* ncurses-5.9
	* udev-150/162 (platform dependent)
	* alsa-utils-1.0.22
	* e2fsprogs-1.41.14
	* evtest
	* freetype-2.3.11
	* libusb-compat-0.1.3
	* openssh-5.8p2
	* qt-everywhere-opensource-src-4.7.2
	* usbutils-0.90
	* expat-2.0.1
	* jpeg-8a
	* linux-2.6.33/2.6.35 (platform dependent)
	* openssl-1.0.0d
	* DeviceKit-disks-009
	* util-linux-2.19.1
	* fbtest-20041102-1
	* libelf-0.8.13
	* mtd-utils-1.3.1
	* strace-4.5.20
	* zlib-1.2.5
	* dbus-1.4.14
	* fbutils-20041102-1
	* libpng-1.2.44
	* procps-3.2.8
	* tslib-1.0
	* ltp-full-20110915
	* ntpclient-2007
	* xconfig
	* eggdbus-0.6
	* gfeeprom
	* glib-2.28.8
	* libsocketcan-0.0.8
	* nano-1.3.12
	* polkit-0.96
	* libmdb

Missing drivers and features:
	CUPID:
		* USB OTG works only in slave mode.
		* OpenVG is not supported yet.

	NESO:
		* USB OTG works only in slave mode.
		* VPU driver is currently not implemented.
		* Video4L output driver is currently not implemented.

	LIVIUS:
		* Display is not supported yet.
		* RS485 is not supported yet.
		* Analog I/O is not supported yet.
		* 1-Wire ist not supported yet.
		* UART 3 (RS232) is not supported yet.
		* Flexcan is not supported yet.

	VINCELL:
		* USB OTG is not supported.
		* CAN is not supported.
		* SATA is not supported.

	General:
		* Video CODECs are not supported yet.
		* 2D accelleration (where exists) is not supported.

Changes:
	* Enabled MDB support in the VINCELL serial driver
	* Added MDB library
	* Added support for Pinnacle capacitive touch screen on CUPID and NESO-LT
	* Added RS485 support on VINCELL
	* Gave the GPIO pins under /sys/class/gpio useful names
	* Updated Garz & Fricke Qt demo application
	* Every touchscreen-enabled platform needs a valid touch configuration
	  in the RedBoot XML data since this release. If an old platform is
	  updated with this new release, RedBoot has to be updated as well
	  (otherwise the kernel will not boot) and a touch configuration file
	  has to be imported (otherwise the touch will not work).


Garz & Fricke Linux BSP V1.5.0				16.04.2012

Released by Tim Jaacks
Verified by Tim Jaacks

Reason for the release:
	* Touch support for VINCELL

Required PTXdist version: 2011.09.0
Required Toolchain:
	* OSELAS.Toolchain-1.99.3 (NESO, CUPID, NESO-LT, LIVIUS)
	* OSELAS.Toolchain-2011.03.1 (VINCELL)
Minimum required RedBoot version: 1.14r2600

Fully supported and tested hardware platforms in this release:
	* VINCELL

All other platforms will probably work, but are to be used at own risk.

Supported Hardware:
* NESO:
	* General board support
	* UART1 (RS232)
	* UART3 (RS458)
	* UART5 (RS232)
	* USB HOST
	* USB OTG (only as slave, untested)
	* NFC
	* Display
	* Ethernet
	* UCB1400 Input Touchscreen
	* UCB1400 ALSA Sound device
	* RTC PCF8583 on I2C1
	* AT24 compatible EEPROM on I2C1
	* LEDs
	* PWM Backlight
	* MMC/SD-Card
	* Digital I/Os

* CUPID:
	* General board support
	* UART1 (RS232)
	* UART2 (RS232)
	* UART3 (RS485)
	* USB HOST
	* USB OTG (only as slave, untested)
	* NFC
	* Display
	* Ethernet
	* UCB1400 Input Touchscreen
	* UCB1400 ALSA Sound device
	* RTC PCF8583 on I2C1
	* AT24 compatible EEPROM on I2C1
	* LEDs
	* PWM Backlight
	* MMC/SD-Card
	* Flexcan1
	* Flexcan2
	* Digital I/Os

* NESO-LT:
	* General board support
	* UART1 (RS232)
	* UART3 (RS485)
	* USB HOST
	* NFC
	* Display
	* PWM Backlight
	* Ethernet
	* CS4265 ALSA Sound device
	* RTC PCF8583 on I2C1
	* AT24 compatible EEPROM on I2C1
	* ADC/TSC Touchscreen
	* MMC/SD-Card
	* Flexcan1
	* Digital I/Os

* LIVIUS:
	* General board support
	* UART 1 (RS232)
	* Ethernet
	* NFC
	* USB Host
	* USB Device
	* RTC PCF8583 on I2C1
	* AT24 compatible EEPROM on I2C1
	* MMC/SD-Card
	* Digital I/Os

* VINCELL:
	* General board support
	* UART 1 (RS232)
	* UART 2 (RS232)
	* Ethernet
	* USB HOST
	* NFC
	* Display
	* PWM Backlight
	* RTC DA9052 on I2C1
	* AT24 compatible EEPROM on I2C1
	* DA9052 Resistive Touchscreen
	* Pinnacle Capacitive Touchscreen
	* EDT FT5X06 Capacitive Touchscreen
	* SGTL5000 ALSA Sound device
	* MMC/SD-Card
	* Digital I/Os

Enabled packages:
	* alsa-lib-1.0.23
	* busybox-1.18.5
	* ftpd support on top of tcpsvd (starting at system startup)
	* canutils-4.0.5
	* dosfstools-3.0.9
	* figlet-2.2.4
	* libusb-1.0.8
	* ncurses-5.9
	* udev-150/162 (platform dependent)
	* alsa-utils-1.0.22
	* e2fsprogs-1.41.14
	* evtest
	* freetype-2.3.11
	* libusb-compat-0.1.3
	* openssh-5.8p2
	* qt-everywhere-opensource-src-4.7.2
	* usbutils-0.90
	* expat-2.0.1
	* jpeg-8a
	* linux-2.6.33/2.6.35 (platform dependent)
	* openssl-1.0.0d
	* DeviceKit-disks-009
	* util-linux-2.19.1
	* fbtest-20041102-1
	* libelf-0.8.13
	* mtd-utils-1.3.1
	* strace-4.5.20
	* zlib-1.2.5
	* dbus-1.4.14
	* fbutils-20041102-1
	* libpng-1.2.44
	* procps-3.2.8
	* tslib-1.0
	* ltp-full-20110915
	* ntpclient-2007
	* xconfig
	* eggdbus-0.6
	* gfeeprom
	* glib-2.28.8
	* libsocketcan-0.0.8
	* nano-1.3.12
	* polkit-0.96

Missing drivers and features:
	CUPID:
		* USB OTG works only in slave mode.
		* OpenVG is not supported yet.

	NESO:
		* USB OTG works only in slave mode.
		* VPU driver is currently not implemented.
		* Video4L output driver is currently not implemented.

	LIVIUS:
		* Display is not supported yet.
		* RS485 is not supported yet.
		* Analog I/O is not supported yet.
		* 1-Wire ist not supported yet.
		* UART 3 (RS232) is not supported yet.
		* Flexcan is not supported yet.

	VINCELL:
		* USB OTG is not supported.
		* CAN is not supported.
		* RS485 is not supported.
		* MDB is not supported.
		* SATA is not supported.

	General:
		* Video CODECs are not supported yet.
		* 2D accelleration (where exists) is not supported.

Changes:
	* Enabled several hardware components on VINCELL
	* Enabled Qt on VINCELL
	* Added general support for different touch screens on all platforms
	* Added automatic touch calibration on boot if no calibration data is present
	* Fixed bug on CUPID: USB OTG port did not work on newer hardware platforms


Garz & Fricke Linux BSP V1.4.0				09.03.2012

Released by Tim Jaacks

Reason for the release:
	* Added audio support on NESO-LT

Required PTXdist version: 2011.09.0
Required Toolchain: OSELAS.Toolchain-1.99.3
Minimum required RedBoot version: 1.14r2600

Fully supported and tested hardware platforms in this release:
	* NESO-LT

All other platforms will probably work, but are to be used at own risk.

Supported Hardware:
* NESO:
	* General board support
	* UART1 (RS232)
	* UART3 (RS458)
	* UART5 (RS232)
	* USB HOST
	* USB OTG (only as slave, untested)
	* NFC
	* Display
	* Ethernet
	* UCB1400 Input Touchscreen
	* UCB1400 ALSA Sound device
	* RTC PCF8583 on I2C1
	* AT24 compatible EEPROM on I2C1
	* LEDs
	* PWM Backlight
	* MMC/SD-Card
	* Digital I/Os

* CUPID:
	* General board support
	* UART1 (RS232)
	* UART2 (RS232)
	* UART3 (RS485)
	* USB HOST
	* USB OTG (only as slave, untested)
	* NFC
	* Display
	* Ethernet
	* UCB1400 Input Touchscreen
	* UCB1400 ALSA Sound device
	* RTC PCF8583 on I2C1
	* AT24 compatible EEPROM on I2C1
	* LEDs
	* PWM Backlight
	* MMC/SD-Card
	* Flexcan1
	* Flexcan2
	* Digital I/Os

* NESO-LT:
	* General board support
	* UART1 (RS232)
	* UART3 (RS485)
	* USB HOST
	* NFC
	* Display
	* PWM Backlight
	* Ethernet
	* CS4265 ALSA Sound device
	* RTC PCF8583 on I2C1
	* AT24 compatible EEPROM on I2C1
	* ADC/TSC Touchscreen
	* MMC/SD-Card
	* Flexcan1
	* Digital I/Os

* LIVIUS:
	* General board support
	* UART 1 (RS232)
	* Ethernet
	* NFC
	* USB Host
	* USB Device
	* RTC PCF8583 on I2C1
	* AT24 compatible EEPROM on I2C1
	* MMC/SD-Card
	* Digital I/Os

* VINCELL:
	* General board support
	* UART 1 (RS232)
	* Ethernet
	* NFC
	* RTC PCF8583 on I2C1
	* Digital I/Os

Enabled packages:
	* alsa-lib-1.0.23
	* busybox-1.18.5
	* ftpd support on top of tcpsvd (starting at system startup)
	* canutils-4.0.5
	* dosfstools-3.0.9
	* figlet-2.2.4
	* libusb-1.0.8
	* ncurses-5.9
	* udev-150/162 (platform dependent)
	* alsa-utils-1.0.22
	* e2fsprogs-1.41.14
	* evtest
	* freetype-2.3.11
	* libusb-compat-0.1.3
	* openssh-5.8p2
	* qt-everywhere-opensource-src-4.7.2
	* usbutils-0.90
	* expat-2.0.1
	* jpeg-8a
	* linux-2.6.33/2.6.35 (platform dependent)
	* openssl-1.0.0d
	* DeviceKit-disks-009
	* util-linux-2.19.1
	* fbtest-20041102-1
	* libelf-0.8.13
	* mtd-utils-1.3.1
	* strace-4.5.20
	* zlib-1.2.5
	* dbus-1.4.14
	* fbutils-20041102-1
	* libpng-1.2.44
	* procps-3.2.8
	* tslib-1.0
	* ltp-full-20110915
	* ntpclient-2007
	* xconfig
	* eggdbus-0.6
	* gfeeprom
	* glib-2.28.8
	* libsocketcan-0.0.8
	* nano-1.3.12
	* polkit-0.96

Missing drivers and features:
	CUPID:
		* USB OTG works only in slave mode.
		* OpenVG is not supported yet.

	NESO:
		* USB OTG works only in slave mode.
		* VPU driver is currently not implemented.
		* Video4L output driver is currently not implemented.

	LIVIUS:
		* Display is not supported yet.
		* RS485 is not supported yet.
		* Analog I/O is not supported yet.
		* 1-Wire ist not supported yet.
		* UART 3 (RS232) is not supported yet.
		* Flexcan is not supported yet.

	VINCELL:
		* No QT support.
		* EEPROM is not supported.
		* CAN is not supported.
		* RS485 is not supported.
		* MDB is not supported.
		* Audio is not supported.
		* USB is not supported.
		* SD/MMC is not supported.

	General:
		* Video CODECs are not supported yet.
		* 2D accelleration (where exists) is not supported.

Changes:
	* Added audio support on NESO-LT
	* Added general board support for VINCELL
	* Enabled NTP client on all platforms
	* Added GUF XML driver for changing system configuration via sysfs
	* A few small bugfixes
	* Upgraded BSP to PTXdist-2011.09.0, resulting in newer versions of
	  several packages


Garz & Fricke Linux BSP V1.2.0				31.08.2011

Released by Hendrik Woidt

Reason for the release:
	* A new main release is needed
	
Supported Hardware:
* NESO:
	* General board support
	* UART1 (RS232)
	* UART3 (RS458)
	* UART5 (RS232)
	* USB HOST
	* USB OTG (only as slave, untested)
	* NFC
	* Display
	* Ethernet
	* UCB1400 Input Touchscreen
	* UCB1400 ALSA Sound device
	* RTC PCF8583 on I2C1
	* AT24 compatible EEPROM on I2C1
	* LEDs
	* PWM Backlight
	* MMC/SD-Card
	* Digital I/Os

* CUPID:
	* General board support
	* UART1 (RS232)
	* UART2 (RS232)
	* UART3 (RS485)
	* USB HOST
	* USB OTG (only as slave, untested)
	* NFC
	* Display
	* Ethernet
	* UCB1400 Input Touchscreen
	* UCB1400 ALSA Sound device
	* RTC PCF8583 on I2C1
	* AT24 compatible EEPROM on I2C1
	* LEDs
	* PWM Backlight
	* MMC/SD-Card
	* Flexcan1
	* Flexcan2
	* Digital I/Os

* NESO-LT:
	* General board support
	* UART1 (RS232)
	* UART3 (RS485)
	* USB HOST
	* NFC
	* Display
	* PWM Backlight
	* Ethernet
	* RTC PCF8583 on I2C1
	* AT24 compatible EEPROM on I2C1
	* ADC/TSC Touchscreen
	* MMC/SD-Card
	* Flexcan1
	* Digital I/Os

* LIVIUS:
	* General board support
	* UART 1 (RS232)
	* Ethernet
	* NFC
	* USB Host
	* USB Device
	* RTC PCF8583 on I2C1
	* AT24 compatible EEPROM on I2C1
	* MMC/SD-Card
	* Digital I/Os

Enabled packages:
	* alsa-lib-1.0.22
	* busybox-1.15.3
	* ftpd support on top of tcpsvd (starting at system startup)
	* canutils-4.0.5
	* dosfstools-3.0.6
	* figlet222
	* libusb-1.0.6
	* ncurses-5.6
	* udev-150
	* alsa-utils-1.0.22
	* e2fsprogs-1.41.9
	* evtest
	* freetype-2.3.11
	* libusb-compat-0.1.3
	* openssh-5.3p1
	* qt-everywhere-opensource-src-4.7.2
	* usbutils-0.86
	* expat-2.0.1
	* jpeg-8
	* linux-2.6.33
	* openssl-0.9.8l
	* DeviceKit-disks-009
	* util-linux-ng-2.17.1
	* fbtest-20041102-1
	* libelf-0.8.13
	* mtd-utils-1.3.1
	* prelink-0.0.20090925
	* strace-4.5.19
	* zlib-1.2.3-ptx4
	* dbus-1.2.16
	* fbutils-20041102-1
	* libpng-1.2.42
	* procps-3.2.8
	* tslib-1.0
	* ltp-full-20100430
	* ntpclient-2007 (CUPID only)
	* xconfig

Missing drivers and features:
	CUPID:
		* USB OTG works only in slave mode.
		* OpenVG is not supported yet.

	NESO:
		* USB OTG works only in slave mode.
		* VPU driver is currently not implemented.
		* Video4L output driver is currently not implemented.

	NESO-LT:
		* Sound is not supperted yet.

	LIVIUS:
		* Display is not supported yet.
		* RS485 is not supported yet.
		* Analog I/O is not supported yet.
		* 1-Wire ist not supported yet.
		* UART 3 (RS232) is not supported yet.
		* Flexcan is not supported yet.

	General:
		* Video CODECs are not supported yet.
		* 2D accelleration (where exists) is not supported.

Changes:
	* Added several new Tests to the LTP framework
	* Enabled the NTP-Client for CUPID
	* several small Bugfixes


Garz & Fricke Linux BSP V1.1.3				21.04.2011

Released by Carsten Behling

Reason for the release:
	* The BSP cannot be built, because the dependency from "gfeeprom"
	  to "kernel" is not present. This leads to a missinfg kernel header.
	* SQLite is needed. for Qt 4.7.2.
		
Supported Hardware:
* NESO:
	* General board support
	* UART1 (RS232)
	* UART3 (RS458)
	* UART5 (RS232)
	* USB HOST
	* USB OTG (only as slave, untested)
	* NFC
	* Display
	* Ethernet
	* UCB1400 Input Touchscreen
	* UCB1400 ALSA Sound device
	* RTC PCF8583 on I2C1
	* AT24 compatible EEPROM on I2C1
	* LEDs
	* PWM Backlight
	* MMC/SD-Card
	* Digital I/Os

* CUPID:
	* General board support
	* UART1 (RS232)
	* UART2 (RS232)
	* UART3 (RS485)
	* USB HOST
	* USB OTG (only as slave, untested)
	* NFC
	* Display
	* Ethernet
	* UCB1400 Input Touchscreen
	* UCB1400 ALSA Sound device
	* RTC PCF8583 on I2C1
	* AT24 compatible EEPROM on I2C1
	* LEDs
	* PWM Backlight
	* MMC/SD-Card
	* Flexcan1
	* Flexcan2
	* Digital I/Os

* NESO-LT:
	* General board support
	* UART1 (RS232)
	* UART3 (RS485)
	* USB HOST
	* NFC
	* Display
	* PWM Backlight
	* Ethernet
	* RTC PCF8583 on I2C1
	* AT24 compatible EEPROM on I2C1
	* ADC/TSC Touchscreen
	* MMC/SD-Card
	* Flexcan1
	* Digital I/Os

* LIVIUS:
	* General board support
	* UART 1 (RS232)
	* Ethernet
	* NFC
	* USB Host
	* USB Device
	* RTC PCF8583 on I2C1
	* AT24 compatible EEPROM on I2C1
	* MMC/SD-Card
	* Digital I/Os

Enabled packages:
	* alsa-lib-1.0.22
	* busybox-1.15.3
	* ftpd support on top of tcpsvd (starting at system startup)
	* canutils-4.0.5
	* dosfstools-3.0.6
	* figlet222
	* libusb-1.0.6
	* ncurses-5.6
	* udev-150
	* alsa-utils-1.0.22
	* e2fsprogs-1.41.9
	* evtest
	* freetype-2.3.11
	* libusb-compat-0.1.3
	* openssh-5.3p1
	* qt-everywhere-opensource-src-4.7.2
	* usbutils-0.86
	* expat-2.0.1
	* jpeg-8
	* linux-2.6.33
	* openssl-0.9.8l
	* DeviceKit-disks-009
	* util-linux-ng-2.17.1
	* fbtest-20041102-1
	* libelf-0.8.13
	* mtd-utils-1.3.1
	* prelink-0.0.20090925
	* strace-4.5.19
	* zlib-1.2.3-ptx4
	* dbus-1.2.16
	* fbutils-20041102-1
	* libpng-1.2.42
	* procps-3.2.8
	* tslib-1.0
	* ltp-full-20100430
	* xconfig

Missing drivers and features:
	CUPID:
		* USB OTG works only in slave mode.
		* OpenVG is not supported yet.

	NESO:
		* USB OTG works only in slave mode.
		* VPU driver is currently not implemented.
		* Video4L output driver is currently not implemented.

	NESO-LT:
		* Sound is not supperted yet.

	LIVIUS:
		* Display is not supported yet.
		* RS485 is not supported yet.
		* Analog I/O is not supported yet.
		* 1-Wire ist not supported yet.
		* UART 3 (RS232) is not supported yet.
		* Flexcan is not supported yet.

	General:
		* Video CODECs are not supported yet.
		* 2D accelleration (where exists) is not supported.

Changes:
	* Build dependency from "gfeeprom" to "kernel" added.
	* SQLite support for Qt 4.7.2 added.

Garz & Fricke Linux BSP V1.1.2				19.04.2011

Released by Carsten Behling

Reason for the release:
	The BSP annot be built , because networking restrictions prevent
    the build system from loading some XML files for eggdbus.
		
Supported Hardware:
* NESO:
	* General board support
	* UART1 (RS232)
	* UART3 (RS458)
	* UART5 (RS232)
	* USB HOST
	* USB OTG (only as slave, untested)
	* NFC
	* Display
	* Ethernet
	* UCB1400 Input Touchscreen
	* UCB1400 ALSA Sound device
	* RTC PCF8583 on I2C1
	* AT24 compatible EEPROM on I2C1
	* LEDs
	* PWM Backlight
	* MMC/SD-Card
	* Digital I/Os

* CUPID:
	* General board support
	* UART1 (RS232)
	* UART2 (RS232)
	* UART3 (RS485)
	* USB HOST
	* USB OTG (only as slave, untested)
	* NFC
	* Display
	* Ethernet
	* UCB1400 Input Touchscreen
	* UCB1400 ALSA Sound device
	* RTC PCF8583 on I2C1
	* AT24 compatible EEPROM on I2C1
	* LEDs
	* PWM Backlight
	* MMC/SD-Card
	* Flexcan1
	* Flexcan2
	* Digital I/Os

* NESO-LT:
	* General board support
	* UART1 (RS232)
	* UART3 (RS485)
	* USB HOST
	* NFC
	* Display
	* PWM Backlight
	* Ethernet
	* RTC PCF8583 on I2C1
	* AT24 compatible EEPROM on I2C1
	* ADC/TSC Touchscreen
	* MMC/SD-Card
	* Flexcan1
	* Digital I/Os

* LIVIUS:
	* General board support
	* UART 1 (RS232)
	* Ethernet
	* NFC
	* USB Host
	* USB Device
	* RTC PCF8583 on I2C1
	* AT24 compatible EEPROM on I2C1
	* MMC/SD-Card
	* Digital I/Os

Enabled packages:
	* alsa-lib-1.0.22
	* busybox-1.15.3
	* ftpd support on top of tcpsvd (starting at system startup)
	* canutils-4.0.5
	* dosfstools-3.0.6
	* figlet222
	* libusb-1.0.6
	* ncurses-5.6
	* udev-150
	* alsa-utils-1.0.22
	* e2fsprogs-1.41.9
	* evtest
	* freetype-2.3.11
	* libusb-compat-0.1.3
	* openssh-5.3p1
	* qt-everywhere-opensource-src-4.7.2
	* usbutils-0.86
	* expat-2.0.1
	* jpeg-8
	* linux-2.6.33
	* openssl-0.9.8l
	* DeviceKit-disks-009
	* util-linux-ng-2.17.1
	* fbtest-20041102-1
	* libelf-0.8.13
	* mtd-utils-1.3.1
	* prelink-0.0.20090925
	* strace-4.5.19
	* zlib-1.2.3-ptx4
	* dbus-1.2.16
	* fbutils-20041102-1
	* libpng-1.2.42
	* procps-3.2.8
	* tslib-1.0
	* ltp-full-20100430
	* xconfig

Missing drivers and features:
	CUPID:
		* USB OTG works only in slave mode.
		* OpenVG is not supported yet.

	NESO:
		* USB OTG works only in slave mode.
		* VPU driver is currently not implemented.
		* Video4L output driver is currently not implemented.

	NESO-LT:
		* Sound is not supperted yet.

	LIVIUS:
		* Display is not supported yet.
		* RS485 is not supported yet.
		* Analog I/O is not supported yet.
		* 1-Wire ist not supported yet.
		* UART 3 (RS232) is not supported yet.
		* Flexcan is not supported yet.

	General:
		* Video CODECs are not supported yet.
		* 2D accelleration (where exists) is not supported.

Changes:
	* Building of the man pages for eggdbus disabled.

Garz & Fricke Linux BSP V1.1.1				13.04.2011

Released by Carsten Behling

Reason for the release:
	The following enhancements are needed.
		* Upgrade to Qt 4.7.2.
		* DeviceKit and DBUS support to detect Storage devices with Qt,
		* OpenSSL support in Qt.
		* QtXMLPatterns support in Qt.
		* QtTest library support in Qt.
		
Supported Hardware:
* NESO:
	* General board support
	* UART1 (RS232)
	* UART3 (RS458)
	* UART5 (RS232)
	* USB HOST
	* USB OTG (only as slave, untested)
	* NFC
	* Display
	* Ethernet
	* UCB1400 Input Touchscreen
	* UCB1400 ALSA Sound device
	* RTC PCF8583 on I2C1
	* AT24 compatible EEPROM on I2C1
	* LEDs
	* PWM Backlight
	* MMC/SD-Card
	* Digital I/Os

* CUPID:
	* General board support
	* UART1 (RS232)
	* UART2 (RS232)
	* UART3 (RS485)
	* USB HOST
	* USB OTG (only as slave, untested)
	* NFC
	* Display
	* Ethernet
	* UCB1400 Input Touchscreen
	* UCB1400 ALSA Sound device
	* RTC PCF8583 on I2C1
	* AT24 compatible EEPROM on I2C1
	* LEDs
	* PWM Backlight
	* MMC/SD-Card
	* Flexcan1
	* Flexcan2
	* Digital I/Os

* NESO-LT:
	* General board support
	* UART1 (RS232)
	* UART3 (RS485)
	* USB HOST
	* NFC
	* Display
	* PWM Backlight
	* Ethernet
	* RTC PCF8583 on I2C1
	* AT24 compatible EEPROM on I2C1
	* ADC/TSC Touchscreen
	* MMC/SD-Card
	* Flexcan1
	* Digital I/Os

* LIVIUS:
	* General board support
	* UART 1 (RS232)
	* Ethernet
	* NFC
	* USB Host
	* USB Device
	* RTC PCF8583 on I2C1
	* AT24 compatible EEPROM on I2C1
	* MMC/SD-Card
	* Digital I/Os

Enabled packages:
	* alsa-lib-1.0.22
	* busybox-1.15.3
	* ftpd support on top of tcpsvd (starting at system startup)
	* canutils-4.0.5
	* dosfstools-3.0.6
	* figlet222
	* libusb-1.0.6
	* ncurses-5.6
	* udev-150
	* alsa-utils-1.0.22
	* e2fsprogs-1.41.9
	* evtest
	* freetype-2.3.11
	* libusb-compat-0.1.3
	* openssh-5.3p1
	* qt-everywhere-opensource-src-4.7.2
	* usbutils-0.86
	* expat-2.0.1
	* jpeg-8
	* linux-2.6.33
	* openssl-0.9.8l
	* DeviceKit-disks-009
	* util-linux-ng-2.17.1
	* fbtest-20041102-1
	* libelf-0.8.13
	* mtd-utils-1.3.1
	* prelink-0.0.20090925
	* strace-4.5.19
	* zlib-1.2.3-ptx4
	* dbus-1.2.16
	* fbutils-20041102-1
	* libpng-1.2.42
	* procps-3.2.8
	* tslib-1.0
	* ltp-full-20100430
	* xconfig

Missing drivers and features:
	CUPID:
		* USB OTG works only in slave mode.
		* OpenVG is not supported yet.

	NESO:
		* USB OTG works only in slave mode.
		* VPU driver is currently not implemented.
		* Video4L output driver is currently not implemented.

	NESO-LT:
		* Sound is not supperted yet.

	LIVIUS:
		* Display is not supported yet.
		* RS485 is not supported yet.
		* Analog I/O is not supported yet.
		* 1-Wire ist not supported yet.
		* UART 3 (RS232) is not supported yet.
		* Flexcan is not supported yet.

	General:
		* Video CODECs are not supported yet.
		* 2D accelleration (where exists) is not supported.

Changes:
	* Upgrade to qt-everywhere-opensource-src-4.7.2.
	* QtTest library enabled with demos.
	* QtXMLPattens enabled with demos.
	* QtOpenSSL support enabled.
	* DevKit disks added to have mass storage detection events on the
	  DBUS system bus.
	* USB keyboard support enabled to be able to type text in Qt test widgets.
	* OpenSSL enhanced that certificates can properly looked up by Qt.
	* gdbserver enabled.
	* STL support in Qt enabled.

Garz & Fricke Linux BSP V1.1.0				24.03.2011

Released by Tim Jaacks

Supported Hardware:
* NESO:
	* General board support
	* UART1 (RS232)
	* UART3 (RS458)
	* UART5 (RS232)
	* USB HOST
	* USB OTG (only as slave, untested)
	* NFC
	* Display
	* Ethernet
	* UCB1400 Input Touchscreen
	* UCB1400 ALSA Sound device
	* RTC PCF8583 on I2C1
	* AT24 compatible EEPROM on I2C1
	* LEDs
	* PWM Backlight
	* MMC/SD-Card
	* Digital I/Os

* CUPID:
	* General board support
	* UART1 (RS232)
	* UART2 (RS232)
	* UART3 (RS485)
	* USB HOST
	* USB OTG (only as slave, untested)
	* NFC
	* Display
	* Ethernet
	* UCB1400 Input Touchscreen
	* UCB1400 ALSA Sound device
	* RTC PCF8583 on I2C1
	* AT24 compatible EEPROM on I2C1
	* LEDs
	* PWM Backlight
	* MMC/SD-Card
	* Flexcan1
	* Flexcan2
	* Digital I/Os

* NESO-LT:
	* General board support
	* UART1 (RS232)
	* UART3 (RS485)
	* USB HOST
	* NFC
	* Display
	* PWM Backlight
	* Ethernet
	* RTC PCF8583 on I2C1
	* AT24 compatible EEPROM on I2C1
	* ADC/TSC Touchscreen
	* MMC/SD-Card
	* Flexcan1
	* Digital I/Os

* LIVIUS:
	* General board support
	* UART 1 (RS232)
	* Ethernet
	* NFC
	* USB Host
	* USB Device
	* RTC PCF8583 on I2C1
	* AT24 compatible EEPROM on I2C1
	* MMC/SD-Card
	* Digital I/Os

Enabled packages:
	* alsa-lib-1.0.22
	* busybox-1.15.3
	* ftpd support on top of tcpsvd (starting at system startup)
	* canutils-4.0.5
	* dosfstools-3.0.6
	* figlet222
	* libusb-1.0.6
	* ncurses-5.6
	* udev-150
	* alsa-utils-1.0.22
	* e2fsprogs-1.41.9
	* evtest
	* freetype-2.3.11
	* libusb-compat-0.1.3
	* openssh-5.3p1
	* qt-everywhere-opensource-src-4.6.2
	* usbutils-0.86
	* expat-2.0.1
	* jpeg-8
	* linux-2.6.33
	* openssl-0.9.8l
	* util-linux-ng-2.17.1
	* fbtest-20041102-1
	* libelf-0.8.13
	* mtd-utils-1.3.1
	* prelink-0.0.20090925
	* strace-4.5.19
	* zlib-1.2.3-ptx4
	* dbus-1.2.16
	* fbutils-20041102-1
	* libpng-1.2.42
	* procps-3.2.8
	* tslib-1.0
	* ltp-full-20100430
	* xconfig

Missing drivers and features:
	CUPID:
		* USB OTG works only in slave mode.
		* OpenVG is not supported yet.

	NESO:
		* USB OTG works only in slave mode.
		* VPU driver is currently not implemented.
		* Video4L output driver is currently not implemented.

	NESO-LT:
		* Sound is not supperted yet.

	LIVIUS:
		* Display is not supported yet.
		* RS485 is not supported yet.
		* Analog I/O is not supported yet.
		* 1-Wire ist not supported yet.
		* UART 3 (RS232) is not supported yet.
		* Flexcan is not supported yet.

	General:
		* Video CODECs are not supported yet.
		* 2D accelleration (where exists) is not supported.

Changes:
	* Added board support for LIVIUS.
	* Added CAN and MMC/SD-Card support on NESO-LT.
	* Improved NESO-LT touch driver (sometimes position 0/0 was reported when touching very softly).
	* Added sysfs entries for digital I/Os on CUPID.
	* Added sysfs entries for keyboard connector digital I/Os on CUPID, NESO and NESO-LT.
	* Replaced Freescale's iMX35 SDHC driver with the mainline driver for better stability on CUPID and LIVIUS.
	* Replaced Freescale's CAN driver with the mainline driver for flexible baudrate setting.
	* Updated the FEC driver to the mainline 2.6.37 version for better stability.
	* Made RS485 switchable between half-duplex and full-duplex via IOCTL on NESO.
	* Fixed bugs in NFC driver (bad block indication, spare size).
	* Fixed backlight brightness issue (did not remain constant during system startup).
	* Removed click noise on CUPID sound output.
	* Added xconfig command line tool to edit XML system configuration (ported from RedBoot with same functionality).
	* Added EEPROM support to all platforms.
	* Added Linux Test Project (LTP) to the BSP.


Garz & Fricke Linux BSP V1.0.3				19.10.2010

Released by Sakire Aytac

Supported Hardware:
* NESO:
    * Genearal board support
    * UART1 (RS232)
    * UART3 (RS458)
    * UART5 (RS232)
    * USB HOST
    * USB OTG (only as slave, untested)
    * NFC
    * Display
    * Ethernet
    * UCB 1400 Input Touchscreen
    * RTC PCF8583 on I2C1
    * AT24 compatible EEPROM on I2C1
    * LEDs
    * PWM Backlight (without LUT support)
	* MMC/SD-Card

* CUPID:
    * Genearal board support
    * UART1 (RS232)
    * UART2 (RS232)
    * UART3 (RS485)
    * USB HOST
    * USB OTG (only as slave, untested)
    * NFC
    * Display
    * Ethernet
    * UCB1400 Input Touchscreen
    * UCB1400 ALSA Sound device
    * RTC PCF8583 on I2C1
    * AT24 compatible EEPROM on I2C1
    * LEDs
    * PWM Backlight (without LUT support)
	* MMC/SD-Card
	* Flexcan1, (Linux SocketCAN driver, currently only with a Bitrate of 500 kBit/s)
	* Flexcan2, (Linux SocketCAN driver, currently only with a Bitrate of 500 kBit/s)

* NESO-LT:
	* Genearal board support
    * UART1 (RS232)
	* UART3 (RS485)
    * USB HOST
    * NFC
    * Display
    * Ethernet
    * ADC / TSC Touchscreen
    

* Features:
	* Enabled packages:
      * alsa-lib-1.0.22
      * busybox-1.15.3
		* ftpd supoort on top of tcpsvd (starting at system startup)
	  * canutils-4.0.5
      * dosfstools-3.0.6
      * figlet222
      * libusb-1.0.6
      * ncurses-5.6
      * udev-150
      * alsa-utils-1.0.22
      * e2fsprogs-1.41.9
	  * evtest
      * freetype-2.3.11
      * libusb-compat-0.1.3
      * openssh-5.3p1
      * qt-everywhere-opensource-src-4.6.2
      * usbutils-0.86
      * expat-2.0.1
      * jpeg-8
      * linux-2.6.33
      * openssl-0.9.8l
      * util-linux-ng-2.17.1
      * fbtest-20041102-1
      * libelf-0.8.13
      * mtd-utils-1.3.1
      * prelink-0.0.20090925
      * strace-4.5.19
      * zlib-1.2.3-ptx4
      * dbus-1.2.16
      * fbutils-20041102-1
      * libpng-1.2.42
      * procps-3.2.8
      * tslib-1.0

Missing drivers and features:
      CUPID:
          * There is a "click noise" while enabling the audio amplifier.
		  * The sound output is unclean.
          * USB OTG works only in slave mode.
		  * Adjustment of the bitrate for the Flexcan Driver not yet implemented.
		  * OpenVG is not supported yet.


      NESO:
          * UCB1400 sound device does not work yet.
          * USB OTG works only in slave mode.
		  * VPU driver is currently not implemented.
		  * Video4L output driver is cuurently not implemented.

		  
	  NESO-LT:
		  * Sound is not supperted yet
		  * Flexcan1 does not work yet.

	  General:
		  * Video CODECs are not supported yet.
		  * 2D accelleration (where exists) is not supported.

Changes:
	  * Link status is reported properly.
	  * Virtual terminals for NESO activated in the kernel.
	  * NESO-LT Hardware support added.
	  * Added backlight look-up-table support, taken from the XML system configuration.
	  * Added screen rotation support in Qt, taken from the XML system configuration.


Garz & Fricke Linux BSP V1.0.2				22.06.2010

Released by Carsten Behling

Supported Hardware:
  * NESO:
    * Genearal board support
    * UART1 (RS232)
    * UART3 (RS458)
    * UART5 (RS232)
    * USB HOST
    * USB OTG (only as slave, untested)
    * NFC
    * Display
    * Ethernet
    * UCB 1400 Input Touchscreen
    * RTC PCF8583 on I2C1
    * AT24 compatible EEPROM on I2C1
    * LEDs
    * PWM Backlight (without LUT support)
	* MMC/SD-Card

  * CUPID:
    * Genearal board support
    * UART1 (RS232)
    * UART2 (RS232)
    * UART3 (RS485)
    * USB HOST
    * USB OTG (only as slave, untested)
    * NFC
    * Display
    * Ethernet
    * UCB1400 Input Touchscreen
    * UCB1400 ALSA Sound device
    * RTC PCF8583 on I2C1
    * AT24 compatible EEPROM on I2C1
    * LEDs
    * PWM Backlight (without LUT support)
	* MMC/SD-Card
	* Flexcan1, (Linux SocketCAN driver, currently only with a Bitrate of 500 kBit/s)
	* Flexcan2, (Linux SocketCAN driver, currently only with a Bitrate of 500 kBit/s)

  * Features:
    * Enabled packages:
      * alsa-lib-1.0.22
      * busybox-1.15.3
		* ftpd supoort on top of tcpsvd (starting at system startup)
	  * canutils-4.0.5
      * dosfstools-3.0.6
      * figlet222
      * libusb-1.0.6
      * ncurses-5.6
      * udev-150
      * alsa-utils-1.0.22
      * e2fsprogs-1.41.9
      * freetype-2.3.11
      * libusb-compat-0.1.3
      * openssh-5.3p1
      * qt-everywhere-opensource-src-4.6.2
      * usbutils-0.86
      * expat-2.0.1
      * jpeg-8
      * linux-2.6.33
      * openssl-0.9.8l
      * util-linux-ng-2.17.1
      * fbtest-20041102-1
      * libelf-0.8.13
      * mtd-utils-1.3.1
      * prelink-0.0.20090925
      * strace-4.5.19
      * zlib-1.2.3-ptx4
      * dbus-1.2.16
      * fbutils-20041102-1
      * libpng-1.2.42
      * procps-3.2.8
      * tslib-1.0

Missing drivers and features:
      CUPID:
          * There is a "click noise" while enabling the audio amplifier.
		  * The sound output is unclean.
          * USB OTG works only in slave mode.
		  * Adjustment of the bitrate for the Flexcan Driver not yet implemented.

      NESO:
          * UCB1400 sound device does not work yet.
          * USB OTG works only in slave mode.

Changes:
	* CAN support for CUPID added
	* MMC/SD-Card support for CUPID and NESO added.
	* RS485 support for CUPID and NESO added.
	* 2nd RS-232 interface support for NESO and CUPID.
	* FTP Server support added for the whole rootfs.
	* LTP (Linux Testing Project) framework introduced.
	
Garz & Fricke Linux BSP V1.0.1				06.04.2010

Released by Carsten Behling

Supported Hardware:
  * NESO:
    * Genearal board support
    * UART1 (RS232)
    * USB HOST
    * USB OTG (only as slave, untested)
    * NFC
    * Display
    * Ethernet
    * UCB 1400 Input Touchscreen
    * RTC PCF8583 on I2C1
    * AT24 compatible EEPROM on I2C1
    * LEDs
    * PWM Backlight (without LUT support)

  * CUPID:
    * Genearal board support
    * UART1 (RS232)
    * USB HOST
    * USB OTG (only as slave, untested)
    * NFC
    * Display
    * Ethernet
    * UCB1400 Input Touchscreen
    * UCB1400 ALSA Sound device
    * RTC PCF8583 on I2C1
    * AT24 compatible EEPROM on I2C1
    * LEDs
    * PWM Backlight (without LUT support)

  * Features:
    * Enabled packages:
      * alsa-lib-1.0.22
      * busybox-1.15.3
      * dosfstools-3.0.6
      * figlet222
      * libusb-1.0.6
      * ncurses-5.6
      * udev-150
      * alsa-utils-1.0.22
      * e2fsprogs-1.41.9
      * freetype-2.3.11
      * libusb-compat-0.1.3
      * openssh-5.3p1
      * qt-everywhere-opensource-src-4.6.2
      * usbutils-0.86
      * busybox-1.15.3
      * expat-2.0.1
      * jpeg-8
      * linux-2.6.33
      * openssl-0.9.8l
      * qt-everywhere-opensource-src-4.6.2-build
      * util-linux-ng-2.17.1
      * fbtest-20041102-1
      * libelf-0.8.13
      * mtd-utils-1.3.1
      * prelink-0.0.20090925
      * strace-4.5.19
      * zlib-1.2.3-ptx4
      * dbus-1.2.16
      * fbutils-20041102-1
      * libpng-1.2.42
      * procps-3.2.8
      * tslib-1.0

Missing drivers and features:
      CUPID:
          * FlexCan support is not yet implemented
          * RS-458 is not yet implemented
          * ESDHC (MMC/SD-Card) support is not yet implemented
          * There is a "click noise" while enabling the audio amplifier.
          * USB OTG works only in slave mode.

      NESO:
          * RS-458 is not yet implemented
          * UCB1400 sound device does not work yet
          * USB OTG works only in slave mode.

Changes:
  * Workaround for phantom triggers implemented.
  * UBI image is enlarged to 64 MB.
  * Creation of a root file system tarball enabled.

Garz & Fricke Linux BSP V1.0.0				31.03.2010

Released by Carsten Behling

Supported Hardware:
  * NESO:
    * Genearal board support
    * UART1 (RS232)
    * USB HOST
    * USB OTG (only as slave, untested)
    * NFC
    * Display
    * Ethernet
    * UCB 1400 Input Touchscreen
    * RTC PCF8583 on I2C1
    * AT24 compatible EEPROM on I2C1
    * LEDs
    * PWM Backlight (without LUT support)

  * CUPID:
    * Genearal board support
    * UART1 (RS232)
    * USB HOST
    * USB OTG (only as slave, untested)
    * NFC
    * Display
    * Ethernet
    * UCB1400 Input Touchscreen
    * UCB1400 ALSA Sound device
    * RTC PCF8583 on I2C1
    * AT24 compatible EEPROM on I2C1
    * LEDs
    * PWM Backlight (without LUT support)

  * Features:
    * Enabled packages:
      * alsa-lib-1.0.22
      * busybox-1.15.3
      * dosfstools-3.0.6
      * figlet222
      * libusb-1.0.6
      * ncurses-5.6
      * udev-150
      * alsa-utils-1.0.22
      * e2fsprogs-1.41.9
      * freetype-2.3.11
      * libusb-compat-0.1.3
      * openssh-5.3p1
      * qt-everywhere-opensource-src-4.6.2
      * usbutils-0.86
      * busybox-1.15.3
      * expat-2.0.1
      * jpeg-8
      * linux-2.6.33
      * openssl-0.9.8l
      * qt-everywhere-opensource-src-4.6.2-build
      * util-linux-ng-2.17.1
      * fbtest-20041102-1
      * libelf-0.8.13
      * mtd-utils-1.3.1
      * prelink-0.0.20090925
      * strace-4.5.19
      * zlib-1.2.3-ptx4
      * dbus-1.2.16
      * fbutils-20041102-1
      * libpng-1.2.42
      * procps-3.2.8
      * tslib-1.0

Missing drivers and features:
      CUPID:
          * FlexCan support is not yet implemented
          * RS-458 is not yet implemented
          * ESDHC (MMC/SD-Card) support is not yet implemented
          * There is a "click noise" while enabling the audio amplifier.
          * USB OTG works only in slave mode.

      NESO:
          * RS-458 is not yet implemented
          * UCB1400 sound device does not work yet
          * USB OTG works only in slave mode.

Changes:
  * Initial version.